Product Details
Product Description
Product Description
Brand:ABB
Type:REF615C_E HCFDACADABC2BAN11E
Origin:the Swiss
Warranty: 365 days
Colour: new/used
Shipping method: Courier delivery
Module of PLC, DCS, ESD system card, the card is a vibration monitoring system, steam turbine control system module, the advantages of the gas generator spare parts brand: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts of our products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on.
INSTALLATION AND COMMISSIONING Installation and wiring of the drive must be completed only by qualified personnel having a basic knowledge of electronics, installation of electronic and mechanical components, and all applicable wiring regulations. Only qualified personnel having broad knowledge of electronics and motion control technology are to commission the machine utilizing the drives. This manual should be read in its entirety. This appendix contains important regulatory information not necessarily covered in earlier chapters. The material in this section should be taken into consideration to ensure compliance with applicable regulatory requirements. This section alone does not contain all the information needed to install and operate an S200 drive. General information on installation and wiring are explained in detail in previous sections. G.4 SAFETY REQUIREMENTS As the user or person applying this unit, you are responsible for determining the suitability of this product for the application. In no event will Danaher Motion be responsible or liable for indirect or consequential damage resulting from the misuse of this product. Read this manual completely to effectively and safely operate the S200. G.5 EUROPEAN COMPLIANCE In Germany, these include: DIN VDE 0100 (instructions for setting up power installations with rated voltages below 1000 V). DIN - EN 60204 - Part 1, (VDE 0113, part 1) instructions relative to electric equipment in machines for industrial use. DIN EN 50178, (VDE 0160) instructions relative to electronic equipment for use in power installations
LOW VOLTAGE DIRECTIVE AND EN50178 To ensure compliance with the Low Voltage Directive and EN50178, following these requirements: Electronic drives contain electrostatic sensitive devices, that can be damaged when handled improperly. Qualified personnel must follow ESD protection measures. For example: wear grounded heel and wrist straps when contacting drive. The climatic conditions shall be in accordance with EN 50178 climatic class: Type B, temperature and relative humidity: Class 3K3. The drives shall be installed in an environment of Pollution Degree 2 or better. The S200 drives are not considered portable and are to be mounted in the intended manner in a motor/control cabinet having adequate strength and thickness with acceptable spacing for the end product classification accessible by qualified personnel only. The enclosure/cabinet shall meet at least the requirements of Protective Type IP2X according to 5.1 of EN 60529. If the top surface of the enclosure/cabinet is easily accessible it shall meet at least the requirements of the Protective Type IP4X. Care shall be taken to ensure that the larger device or enclosure that accommodates the built-in device provides protection against direct contact. The S200 drives may be erected in closed electrical operating areas if a protection against direct contact is available or assigned for by means of obstacles and/or a distance according to IEC 364-4-412.3 and IEC 364-4-412.4. Follow IEC 536-2 and IEC 1140 for installation protection against electric shock. Installation shall be performed in accordance with local electric codes, local accident prevention rules, EN 50178 and EN 61800-3. Never connect or disconnect any drive connectors or terminals while the power is switched on.
>>
pattern design restroom aluminum door
>>
230V Mini Hand Saw Circular Saw Machines Factory
>>
Baby Scooter Have Basket Factory Directly Wholesale New Design Kids Toy Car
>>
Hydraulic Car Lift Car Lift to Park 2t 4.5m 3X6m Platform
>>
73Galvanized Thickness Gauge|Galvanized layer thickness gauge|Galvanized online thickness gauge|Galvanized coating thickness detector
>>
Max Rb441t, Rb611t Steel Bar Binding Machine Automatic Electric Hardware Tool Wire Hook Artifact Intelligent Twin Wire Rebar Binding Machine
>>
2in1 Multifunction Milling and Drilling Machine Zay7032fg/1 Zay7040fg/1 Zay7045fg/1
>>
Contemporary Home Furniture Plywood Sanitary Ware Bathroom Cabinet with LED Light
>>
4-48 Core Om3 Muti Purpose LSZH PVC Hatrel Break-out Distribution Indoor FTTH Fiber Optical Cable
>>
Special Turret Double Spindle CNC Metal Lathe with CE/ISO (ESY1200MS)
>>
Premium Frozen Diced Ginger - Affordable Bulk Supply for Resellers
>>
Fabric Industry Broken Needle Metal Detector for Clothing
>>
For BMW 3 Series F30 F35 change to M3 Copy style body kit bumpers
>>
Hr Double-Stage for Chemical Industry
>>
2025 Popular 36V 240W Fat Tire Mountain Bike E City Bicycle Sports Pedal Assist Electric Bike
>>
Chinese Hot Sale Cheap Good Quality 10HP 18HP 12HP 20HP Two Wheel Walking Tractor
>>
4 Axis CNC Countertop Cutting Machine
>>
Plastic Film Washing Waste Film Recycling Machine Plastic Recycling Machinery
>>
V Shape Powder Mixing Machine Mixer Blender
>>
Pet PP HDPE PE Water Drink Bottle Plastic Bale Opener /Breaker Machine
