Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN4580-TV | 45 | 80 | 60 | 42.5 | – | – | 25 |
| 70 | – | – | 11.5 | – | – | 0.3 | 0.6 |
|
| 71 | 60 | 61,000 | 177,000 | 38,000 | 74,000 | 4,000 | 1,500 | 1.2 | 3,000 | 1,340 | 5.33 | 1 | 1.12 |
| ZARN4580-L-TV | 45 | 80 | – | – | 75 | 57.5 | 25 |
| 70 | 56 | 68 | 11.5 | 26.5 | 12 | 0.3 | 0.6 |
|
| 71 | 54 | 61,000 | 177,000 | 38,000 | 74,000 | 4,000 | 1,500 | 1.2 | 3,000 | 1,340 | 6.03 | 1 | 1.27 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
High Efficiency 5t/H Output Orchards Feed Mill Machine for Sale
>>
High-End Wc67K Hydraulic Press Brake with E21 Display Technology
>>
School Classroom Furniture Movable Green White Board
>>
mask making Meltblown cloth Slitting rewinder Slitter Machine
>>
China Factory Digital Eco Solvent Printer Galaxy 3.2m Size I3200 4 Printer Heads
>>
RF Coaxial TNC Female to N male Adapter
>>
Hengpu 1K Grey Primer Supplier Good Adhension Acrylic Car Paint Refinish Lacquer Easy Operation Auto Paint
>>
Precision Plastic Injection Mould for Home Appliance
>>
China Top Quality Ce Ship Unloader Manufacture for Series Grain Transportation
>>
High-Performance Full Suspension Carbon MID Drive Electric Mountain Bike for Adventurers
>>
upgrade to full LED 4 lens headlamp headlight front lamp with dynamic for TOYOTA 4 RUNNER head lamp head light 2014-2021
>>
Dk77100 CNC Wire EDM Cutting Machine High Quality
>>
Double Head LED Wall Light 5W 7W Balcony Lamp Waterproof Outdoor Lighting
>>
Grade a Healthy Snack Freeze Vegetable Frozen Carrot Slice IQF Sliced Carrots
>>
Taijia pundit test concrete Structural concrete compressive strength Nonmetal Ultrasonic Apparatus
>>
China Manufactured Hydraulic Filter Press for Ceramic Plant
>>
High Temperature Resistant Pressure Vessel Stainless Steel 310S Separator
>>
Wnq Best Price Black Flat Bench Chair for Sale
>>
CE China Factory Small Hydraulic Metal Bending Folding Machine 50 Ton 1600 for Sale
>>
300m Giant Inflatable Slip N Slide Inflatable City Slide Inflatable Water Slide For Event
