Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN3080-TV | 30 | 80 | 66 | 43 | – | – | 20 |
| 68 | – | – | 14 | – | – | 0.3 | 0.6 |
|
| 69 | 52 | 107,000 | 265,000 | 26,000 | 47,000 | 4,400 | 1,300 | 2.1 | 3,300 | 1,100 | 6.53 | 1 | 1.5 |
| ZARN3080-L-TV | 30 | 80 | – | – | 82 | 59 | 20 |
| 68 | 52 | 66 | 14 | 30 | 12 | 0.3 | 0.6 |
|
| 69 | 50 | 107,000 | 265,000 | 26,000 | 47,000 | 4,400 | 1,300 | 2.1 | 3,300 | 1,100 | 7.43 | 1 | 1.7 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
29er Shimano Aluminum Hardtail E-Bike Frame Ep8/E6000 Series Emtb Pedelec
>>
PCB Ud101 Solar Charge Controller 3.7V PCB for Arduino Lvds Board Factory
>>
Big ABS ASA Extruded Radome Plastic Profile
>>
Lower Price Summer Yurt Family Tourist Hiking Tents Outdoor Camping Dome Tent
>>
Vertical and Horizontal Multifunctional Drilling and Milling Machine
>>
For NISSAN Timing Chain Tensioner OEM NO.1307040F06 TN9023
>>
104cm Kamado Tanjirou Katana Carbon Steel Demon Slayer Sword
>>
Jhc Furniture Metal Dinette Set with Laminated Natural Luxurious Stone Rectangular Marble Dining Table for Living Room
>>
Corn Wheat Paddy Rice Combine Harvester
>>
USB3.0 HDMI Waterproof Extension Power Cable for Car Truck Boat Motorcycle
>>
High-Performance Servo Injection Molding Machine for Plastic Solutions
>>
Agriculture Machinery Equipment Small Mini Wheel Tractor Price Tractor OEM
>>
Pillar-Typr Gear Drive Drilling Machine (D4)
>>
China Wholesale High Quality Fancy Bamboo Twins Chopsticks for Family
>>
86-Inch Ultra HD Interactive Touch Screen Meeting Display
>>
PFEA112-20 3BSE030369R0020 ABB module supply
>>
Top mill scale briquette press machine supplies
>>
Taijia TM 8810 Metal/Pvc/Glass Any hard materiald Ultrasonic thickness meter gauge
>>
Automatic High Speed Single Nozzle Down and Cotton Integrated Filling Machine with Weighing System (RM1-6)
>>
Ht-90 Single Stage Water Cooling Plastic Recycling Pelletizer Machine
