Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN2557-TV | 25 | 57 | 50 | 35 | – | – | 20 |
| 47 | – | – | 10 | – | – | 0.3 | 0.6 |
|
| 48 | 39 | 35,500 | 86,000 | 22,600 | 36,000 | 6,000 | 1,900 | 0.55 | 1,900 | 350 | 0.989 | 1 | 0.53 |
| ZARN2557-L-TV | 25 | 57 | – | – | 65 | 50 | 20 |
| 47 | 36 | 45 | 10 | 25 | 11 | 0.3 | 0.6 |
|
| 48 | 34 | 35,500 | 86,000 | 22,600 | 36,000 | 6,000 | 1,900 | 0.55 | 1,900 | 350 | 1.15 | 1 | 0.59 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
China Manufacturer Office Furniture High Back Mesh Ergonomic Executive Swivel Office Chair
>>
Amada CO2 Laser Cutting Machine Upgrade to Fiber Laser Cutting Machine Lcg3015 Fo3015 Fo3015miint Lcg30151nt Fol3015 Lca3015 Amada CO2 Laser Cutting Machine
>>
Custom Diary Notebook Gift Set Luxury PU Leather Hardcover Notebook
>>
Calf Diarrhea Test Bovine Coronvirus-Rotavirus-Cryptosporidium-Giardia Lamblia-Escherichia Coli K99 Antigen Combo Test
>>
Taijia digital load cell Stainless Steel Telemetry Load Link Crane Scales and Load Cells Indicators Dynamometers
>>
11 Heads 14 Heads Granite Marble Edge Grinding and Polishing Machine
>>
Dual Axis CNC Lathe, Dual Tool Holder, Four Coordinate CNC Machine Tool Tck56-500
>>
Modern Rattan Home Design Wooden Storage Cabinet with Metal Frame
>>
Built in printer of GPS digital tachograph with speed limiting function
>>
Animal Feed Pellet Processing Machine at Sale
>>
Milling Machine (ZX6350ZA ZX6350ZB)
>>
Keysight U1232A Handheld Digital Multimeter 3 ½ Digit Test Resistance Current
>>
Fashion Candy Colors Cationic Shoe Bag Business Trip for Male and Female
>>
Contemporary main entrance tempered glass black color handcraft grills styles wrought iron exterior single door with sidelights
>>
Professional Conveyor Belts Splicer/Conveyor Belt Joint Vulcanizing Press
>>
performance tip silencers for BMW 5 series G30 G38 exhaust tip
>>
Xugong 1.2m Small Cold Planer Xm120f Road Milling Machine Lathe Multifunction Milling Machine for Sale
>>
Custom Printed Boxing Gloves Genuine Cowhide Wholesale Pu Leather OEM Logo Packing Color Material Origin Place Model Customer
>>
High Precision Fanuc/GSK CNC Horizontal Machining Center Metal Lathe CNC Milling Machine 5 Axis
>>
Sunflower Seeds/Sunflower Oil/Sun Flower Seeds
