Marine Pneumatic Rubber Airbag for Ship Launching

Product Description

Marine Pneumatic Rubber Airbag for Ship Launching
Marine Rubber Airbags
Air bag for heavy lifting and transportation and ship launching is an innovative product with independent intellectual property rights in China. At present, it has been widely used in ship launching, caisson lifting and transportation, handling of other heavy objects, and floating aid of underwater installation engineering. The application of marine air bag is less limited by the site, and does not need large-scale mechanical equipment, so it can shorten the engineering period and save a lot of money. After more than 20 years of development and practice, it has been proved that this product has the characteristics of safety, high efficiency, green environmental protection, flexibility and so on.
The production and application of marine airbags mainly refer to two industry standards: CB / t3795 "airbags for ship discharge and launching" and CB / T3837 "technical requirements for upper discharge and launching of ship airbags".
In the basic requirements and evaluation methods for production conditions of shipbuilding enterprises formulated by the Commission of science, technology and industry for national defense, air bag launching is included as an approved launching method for the first time, and it is stipulated that class II and class I enterprises are allowed to use air bag launching mode. Meanwhile, corresponding requirements are put forward for the equipment using air bag launching.
Maintenance of Marine Airbags
When the air bag is not used for a long time, it should be washed and dried, filled with talcum powder inside and outside, and placed in a dry, cool and ventilated place indoors. The air bag shall be stretched out and placed horizontally, and no heavy objects shall be piled on the air bag.
Keep the air bag away from heat sources.
The air bag should not be in contact with acid, alkali, grease and organic solvent.
Repair of Marine Airbags
The damage forms of marine airbags can be generally divided into longitudinal cracks (cracks extending along the length of airbags), transverse cracks (cracks extending along the circumference), and nail holes (including disc-shaped damages with a diameter of less than 10 cm).
The operation steps are as follows:
1) Mark out the scope of repair as the boundary of the polished surface. The scope of repair should be extended around the crack, and no hidden injury should be missed. The expansion range varies according to the type and damage range of the airbag, which is usually 18-20cm for three layers, 20-22cm for four layers, 22-24cm for five layers and 24-26cm for six layers. Laying of cord fabric with longitudinal crack.
2) Grind the surface of the repaired part until the fiber thread is exposed, but do not damage the fiber line.
3) For long cracks, the cord thread should be used to sew the long cracks. The distance between needle holes and cracks is about 2-3cm, and the distance between stitches is about 10cm.
4) Clean the surface to be repaired with gasoline and cool dry.
5) Apply a layer of glue. Mucilage is made from raw rubber and soaked in gasoline. The weight ratio of raw rubber to gasoline is usually 1:5, and it should be slightly thinner when coating the first layer (the weight ratio of raw rubber to gasoline can be 1:8). After the first layer of mucilage is dried, apply a slightly thicker glue and dry it.
6) Seal the crack with the raw rubber strip with thickness of 1 mm and width of 1 cm larger than the crack.
7) Brush the gasoline and dry.
8) For longitudinal cracks, first apply a layer of hanging cord cloth perpendicular to the crack direction with a width of about 10cm. For transverse cracks and nail holes, step (10) can be operated directly.
9) Brush the gasoline and dry.
10) Lay a layer of hanging cord fabric parallel to the longitudinal direction. The lap area around the crack should be more than 5cm, and the edges should be cut into rounded corners
11) Brush the gasoline and dry.
12) Lay a layer of hanging rubber cord fabric obliquely. The direction of the cord should be the same as that of the diagonal cord (or reinforcing fiber) in the bag wall. The lap area around shall be 1cm larger than that of the previous layer of cord fabric, and the edges shall be cut and pasted into rounded corners
13) Brush the gasoline and dry.
Welcome to contact Deyuan Mairne for different sizes of Marine Airbags with very Competitive price, specs, drawings to support you Nice Quality airbags.
Technical Paremeter of Rubber Airbags

---

>> Manufacturer Good Quality Carbide Corner Radius Milling Cutters
>> Factory Customization Long Life Service Punch Mesh Panel Perforated Metal Mesh Windproof Fence
>> High Precision CNC Gun Drill Grinding Machine Gd-36/26/20 From China Supplier
>> Male Solid Stainless Seel Silver High Polish Cross Ring
>> 300W/500W/600W/800W/1000W/1200W IP66 Waterproof 190lm/W LED Flood Lighting Stadium Projector LED Floodlight Sport Light
>> PU Leather Ladies Crossbody Bag for Women New Handbag Fashion Wallet (MFN7442)
>> 3/8" 110V Portable High Pressure Hydraulik AC Air Conditioning Hidraulic Atco Industrial P32 Hydraulic Rubber 2 Air Hose Pipe Crimper Machine CNC Manual Dx68
>> VB-150T Vertical Plastic Baling Machine Baler
>> 1000kg Feed Mixer with High Mixing Homogeneity for Animal Feed Production
>> Anime Fate Grand Order Okita Souji Cosplay Toy Wooden Sword
>> Home Kitchen Cast Iron Skillet Round fry Steak pan
>> Pig Drinking Bowl Unique New Animal Drink Bowl
>> F-102 Fire Security Pull Station
>> Aftermarket power liftgate automatic tailgate kit smart auto electric tail gate lift for kia sportage 2016 2017 2018 2019 2020
>> Ribbon Blender Spice Salt Powder Mixer
>> Cheap Price Graphic Card 4000 GPU Video Card
>> Custom Wholesale 100% Cotton High Visibility Reflective Men Long Sleeve Work Wear Uniform Safety Work Shirts
>> Scania Truck Parts Valve Housing 2082090 2760914 1493769 2447369
>> 2020 New Hzs60 Concrete Mixer Machine Manufacturer Price in Nepal
>> 400W 48000lm Outdoor Aluminum LED Street Light