Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN5090-TV | 50 | 90 | 60 | 42.5 | – | – | 25 |
| 78 | – | – | 11.5 | – | – | 0.3 | 0.6 |
|
| 79 | 67 | 90,000 | 300,000 | 40,000 | 82,000 | 3,600 | 1,200 | 2.2 | 4,800 | 2,470 | 8.42 | 1 | 1.43 |
| ZARN5090-L-TV | 50 | 90 | – | – | 78 | 60.5 | 25 |
| 78 | 60 | 78 | 11.5 | 29.5 | 12 | 0.3 | 0.6 |
|
| 79 | 58 | 90,000 | 300,000 | 40,000 | 82,000 | 3,600 | 1,200 | 2.2 | 4,800 | 2,470 | 10.46 | 1 | 1.78 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Organic Synthetic Fiber Aramid Pulp Has Good Dispersibility, High Tearing Strength and Good Price
>>
Dm-400 Top-Down DLP 3D Printer for Precision Prototyping
>>
Edical Adhesive Tape Made of Pure Cotton, Used for Wrapping Wounds on Cracked Hands and Feet
>>
Hsy128 Mattress Production Line Industrial Automatic Fabric Sewing Textile Shuttle Multi Needle Single Quilting Machine
>>
Tensioner pulley replacement tensioner pulley autozone 0K972-12-700 FE1H-12-700A VKM74600 GT20010 CR50 for Japanese car
>>
Car Lift Two Post Car Lift Hydraulic Lift Vehicle Maintenance Equipment
>>
2019 Good Quality stainless steel electric pineapple peeler and corer
>>
Versatile Power Tool Gear for Professional and DIY Use Precision Mould
>>
Car front Fog lamp Auto Parts front Fog light for hyundai i10 2014 92202-B4010 92201-B4010
>>
High Quality Factory Price Branch Crusher High Horsepower Drum Wood Chipper Mobile Diesel Wood Crusher
>>
Big Motorcycle Bike Insulated Delivery Food Bag To Keep Food Hot Fast Food Delivery Bag
>>
Powerful Brushless Electric Impact Drill Drilling Machine
>>
Bin Big Disposable Trash Bags Heavy Duty Rubbish Plasticthicken Garbage Bag
>>
WMTCNC small cnc milling machine VMC650L vertical matal machining center
>>
Insulation Fiberglass Sheet G10/ FR4 Epoxy Laminating Sheet
>>
Yovon CS-8 Paper Tube Paper Core Making Winding Rolling Machine/ID30-100mm/Max Length 1200mm
>>
Stainless Steel Chain PE Film Bottles Shrink Packing Machine
>>
Performance Racing Leaf Spring 8 inch for 3 inch Axle Tube U-Bolt
>>
Plain blank wholesale custom hoodie pullover high quality hoodies for men
>>
200-500kg/H Barbecue Used Briquette Machine
