Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN1747-TV | 17 | 47 | 43 | 29.5 | – | – | 16 |
| 38 | – | – | 9 | – | – | 0.3 | 0.6 |
|
| 39 | 28 | 26,000 | 57,000 | 14,000 | 19,900 | 7,800 | 2,100 | 0.4 | 1,600 | 160 | 0.373 | 1 | 0.37 |
| ZARN1747-L-TV | 17 | 47 | – | – | 57 | 43.5 | 16 |
| 38 | 28 | 38 | 9 | 23 | 11 | 0.3 | 0.6 |
|
| 39 | 26 | 26,000 | 57,000 | 14,000 | 19,900 | 7,800 | 2,100 | 0.4 | 1,600 | 160 | 0.464 | 1 | 0.41 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Food grade Custom logo transparent laminated vacuum seal packaging bags vacuum food pack plastic bags
>>
Holiauma 10 Years Quality Warranty Holihope 8 Head China Factory Computer Industrial Quilting Tajima Similar Embroidery Machine Price Made in China for Sale
>>
Home Outside Package Locker Waterproof Metal Steel Letter Mail Mailbox Post Wall Mount Smart Parcel Delivery Drop Box
>>
Monobloc Filling and Capping for Antiseptic Handwash
>>
Coat Dustproof Cover Travel Multi-Purpose Suit Packing Dress Bags Garment
>>
Full Automatic Blanking Machine Medicine Box Tobacco Box Stripping Machine After Die Cutter Box Offline Blanking Stripping Machine for Folding Box
>>
High Voltage 100kw 150kw 200kw Hybrid on off Grid Solar System for Commercial Use
>>
Puff Snack Making Machine (Chip/Cracker/Cheese Ball/cereal extruder)
>>
Fiber Laser Cutting Machine 1000W 2000W Metal Plate Sheet Pipe Tube Laser Cutter Machine
>>
Liquid Homogenizer for Legume Milks / Nut Milks / Seed Milks
>>
Large Waterproof Durable Motorcycle Pizza Delivery Box Insulated Food Delivery Backpack Cooler Box Shoulder Bag Outdoor Acoolda
>>
81130-52D70 81170-52D70 Auto Parts High Quality Headlight Head Lamp for Vitz 2012 Yaris 2012
>>
High quality customized hard PE plastic UHMWPE board for sale
>>
Outdoor gazebos aluminum louvre roof pergola with weatherproof system
>>
Vertical Mixer
>>
3D Protection Wide Area Security Radar That Can Detect Target up to 60m for Wide Area Protection Radar for Wide-Area Surveillance Monitoring Security Radar
>>
Multifunctional High Pressure Vessel For Wholesales 4040 Frp Pressure Vessel
>>
with Punching Part Cable Tray Making Roll Forming Machine
>>
NP Series Coating Paper Production Line
>>
Cost Effective High Power Motor Heavy Duty Manufacturer CNC Mill Turn Machine
