Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN1545-TV | 15 | 45 | 40 | 28 | – | – | 16 |
| 35 | – | – | 7.5 | – | – | 0.3 | 0.6 |
|
| 36 | 28 | 24,900 | 53,000 | 13,000 | 17,500 | 8,500 | 2,200 | 0.35 | 1,400 | 110 | 0.24 | 1 | 0.34 |
| ZARN1545-L-TV | 15 | 45 | – | – | 53 | 41 | 16 |
| 35 | 24 | 34 | 7.5 | 20.5 | 11 | 0.3 | 0.6 |
|
| 36 | 22 | 24,900 | 53,000 | 13,000 | 17,500 | 8,500 | 2,200 | 0.35 | 1,400 | 110 | 0.274 | 1 | 0.37 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Stainless Steel Fork Felting Needle for Punching Machine Kitchen Gadget Sea Food Tool
>>
aluminium window for house toilet casement window top hung window with double glass for australian standard
>>
Special-Shaped Fluorescent Sticky Notes, Memo Pads, Notepads in Irregular Shapes
>>
Advertising Machines Industrial Mini PCS Intel Core I5-8260u DDR4 SSD Win10PRO Win11 Mini Computer Patron Self-Check & Payment Kiosks
>>
5000-10000L Sf Double Wall Underground Diesel Fuel Tank Oil Fuel Storage Tank Double Wall Tank
>>
XCMG Used Hydraulic Lift 14m-Level Articulating Lift Platform
>>
Freight Forwarder From China to USA International Fba Shipping Freight DDP Door-to-Door
>>
High Strength ASTM Standard 200/300/800 825 840 Series N08825 N08800 2.4858 1.4876 Welded Stainless Steel Pipe Electric Heating Tube Titanium
>>
Vmc 2190vs Vertical Machining Center Four Rail Heavy Duty Machining Center Fanuc Siemens Controller
>>
Fast Processing Laser Tube Cutting Machine 3kw 6kw Metal Sheet Plate Tube Fiber Laser Cutting Machine for Sale
>>
Outdoor Badminton Net Frame Portable Shuttlecock Posts
>>
Beauty Salon Rotary Lamp LED Barber Shop Floor Lamps Barber Pole
>>
Environmental Friendly Automatic Concrete Block Machine for Efficient Brick Production Process
>>
Computerized Lock Stitch Multi-Needle Mattress Quilting Machine Hy-128-3b
>>
Automotive Car Parts Car Bumper For Mercedes Benz GLS X167 Upgrade GLS63 AMG Grille Rear Diffuser Wheel Arch Rear Tip Body Kits
>>
Digital Photo Frames Nft Art Frame APP Controlled Digital Photo Frame
>>
Handheld logo manual serial printing machine
>>
Mini Tiller Gt590
>>
Made in China Investment Casting Custom Stainless Steel Square Box
>>
China GS Approved Metal-Cutting Tools Machining Center Vertical CNC Gantry Milling Machine
