Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN65125-TV | 65 | 125 | 82 | 53.5 | – | – | 25 |
| 110 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 111 | 97 | 172,000 | 500,000 | 54,000 | 104,000 | 2,600 | 900 | 4 | 4,800 | 4,000 | 51 | 1 | 4 |
| ZARN65125-L-TV | 65 | 125 | – | – | 103 | 74.5 | 25 |
| 110 | 90 | 108 | 17.5 | 38.5 | 16 | 0.3 | 0.6 |
|
| 111 | 88 | 172,000 | 500,000 | 54,000 | 104,000 | 2,600 | 900 | 4 | 4,800 | 4,000 | 60.1 | 1 | 4.6 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Auto Car LED Tail Light Car Lamp For Vitz yaris 2012 - 2014
>>
Hpe Proliant Dl380 Gen10 Win 2019 Standard Media GPU 2u Rack Server
>>
CNC 5+1 Axis Stone Processing Machine Multipurpose with Factory Price
>>
Professional ce approved sawdust rice husk charcoal briquette press charcoal making machine
>>
304 Stainless Steel Large Pet Cat/dog Grooming Bath Tub
>>
Hot and cold high straight bathroom gun metal faucet mixer brass bathroom basin faucet
>>
Bidirectional DC/DC Converter Buck Boost DC DC Converter with Air Liquid Cooling
>>
Ewelink Tuya Zigbee WiFi Smart Energy Meter Voltage Current Protector Circuit Breaker
>>
Wholesale Printers High Quality Toner for Use in 2000/2300n/2700n/3500n/3501n/4500n/4501n
>>
5SHY4045L0001 3BHB018162R0001 ABB IGCT CONTROLLER 24 MONTHS WARRANTY
>>
Badminton Shuttlecock Good Stable Flight Goose Feather Same as Lingmei 80
>>
Stainless Steel Short Path Wiped Film Evaporator Molecular Distillation
>>
Aluminium Alloy 5050 Wire 3.97mm for Rivet/5056 5083 5086 5154 5182 High Quality Aluminum Wire Copper Wire Brass Wire 5356 Aluminum Wire
>>
FT8210H Electromagnetic-Inductive Flow Sensor Electronic Flow Meter Electromagnetic Flow Converter
>>
High Quality Paper Cup Production Making Machine Price, Paper Cup Making Machine
>>
Stainless Steel 304/303/316 Custom Made Steel Lathe Turning
>>
ppgi prepainted color coated galvanized steel coil 914/1219/1220/1250
>>
High Quality Low Price Plastic Cable Drag Chain
>>
75kw Mining Equipment Diamond Wire Saw Machine for Granite Marble Quarry
>>
Manufacturers Make 3D Printers Metal Printer
