Product Details
Product Description
Product Description
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
Setting the Auto-zero mode to Once improves the accuracy of the measurement. With auto-zero enabled, the inputs of the SCXI-1141/1142/1143 are internally grounded. The driver makes a measurement when the task begins and then subtracts the measured offset from all future measurements. Although the DAQ driver does wait a certain amount of time for the signal to settle, it may not be long enough if the filter is set to very low cutoff frequency. This is especially true if the voltage ever goes out of range and the amplifier becomes saturated. You can manually zero out the offset by comparing the ground coupled value of a channel to its DC coupled value, then subtracting that offset from future measurements. This allows you to control the time allowed for the signals to settle. Configurable Settings in MAX Note If you are not using an NI ADE, using an NI ADE prior to version 8.3, or are using an unlicensed copy of an NI ADE, additional dialog boxes from the NI License Manager appear allowing you to create a task or global channel in unlicensed mode. These messages continue to appear until you install version 8.3 or later of an NI ADE. This section describes where you can access each software-configurable setting in MAX. The location of the settings varies depending on the version of NI-DAQmx you use. Refer to the DAQ Getting Started Guide and the SCXI Quick Start Guide for more information on installing and configuring the hardware. You can use DAQ Assistant to graphically configure common measurement tasks, channels, or scales.Configurable Settings This section describes how to set the gain/input signal range and how to configure your software for compatible sensor types. It also describes how to perform configuration of these settings for the SCXI-1141/1142/1143 in NI-DAQmx. For more information on the relationship between the settings and the measurements and how to configure settings in your application, refer to Chapter 4, Theory of Operation. Common Software-Configurable Settings This section describes the most frequently used software-configurable settings for the SCXI-1141/1142/1143. Refer to Chapter 4, Theory of Operation, for a complete list of software-configurable settings. Gain/Input Range Gain/input range is a software-configurable setting that allows you to choose the appropriate amplification to fully utilize the range of the E/M Series DAQ device. In most applications NI-DAQ chooses and sets the gain for you determined by the input range. This feature is described in Chapter 4, Theory of Operation. Otherwise, you should determine the appropriate gain using the input signal voltage range and the full-scale limits of the SCXI-1141/1142/1143 output. You can select a gain of 1, 2, 5, 10, 20, 50, or 100 on a per channel basis. Chapter 3 Configuring and Testing SCXI-1141/1142/1143 User Manual 3-2 Input Selection The front end of the SCXI-1141/1142/1143 includes a software configurable switch that allows you to programmatically connect the input channels of the SCXI-1141/1142/1143 to either the front connector or internal ground. Refer to Table 5-1, NI-DAQmx Voltage Measurement Properties, for details about the available input coupling modes supported by the SCXI-1141/1142/1143.
>>
Storage holders & racks Dish Drainer Racks Kitchenware Stainless Steel Kitchen Plate Drying Rack
>>
Casual Style Indoor High Quality High Elastic Non-Slip EVA Slippers
>>
Chia Seeds Retail
>>
Blue Customized Sublimation Polo Shirt with Short Sleeves
>>
3HAC5497-1 ABB module supply
>>
Factory Direct Sales Outdoor Wireless Battery PAR Light 12*18W RGBWA UV 6in1 Waterproof PAR Light
>>
Et-F Series Compound Two-Stage Freezing Screw Compressor
>>
Fully Automatic Office Guillotine Cutting Machine Hydraulic Paper Cutter Multi Purpose A4 Paper Cutting Machine
>>
Hot Sale Ore Grinding Machine Ball Mill for Gold and Copper Mining
>>
2024 New Electric Scooter 60V20ah EEC Electric Moped Scooter 1600W 2000W Electric Motorcycle Electric Motorbike Adult
>>
UL Listed 57/68/79/93 Concealed Pendent Quick Response Fire Sprinkler
>>
Popular Universal Milling Machine High Speed Universal Rotary Head Milling Machine
>>
Logi G304 Wireless Mouse 6 Programmable Buttons USB Wireless Mouse Hero Sensor 12000dpi Adjustable Manufacture
>>
PV Solar System Cost of Stand Alone Solar Power System 5kw 5000W 10kw 25kw 15kw Hybrid Solar Home off Grid Solar Power Energy System with Power Inverter
>>
Rt-80fa Fully Automatic Double Head Short Material Hydraulic Chamfering Machine
>>
fog lamp frame strip for tersla model x 1049609 1049610 1049611,1049612
>>
stainless steel garlic peeling machine garlic peeler
>>
Horizontal Pillow Wrapper Biscuits / Croissants / Muffins Flow Pack Machine
>>
Heavy-Duty Vertical Electric Hydraulic Scissor Lift Table Truck
>>
Fanuc and CE Certificate CNC Drilling Machinery Fortube Plate Market (ZJG08-4020)
