Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN60120-TV | 60 | 120 | 82 | 53.5 | – | – | 25 |
| 105 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 106 | 90 | 187,000 | 550,000 | 44,500 | 92,000 | 2,700 | 950 | 4.2 | 5,300 | 4,300 | 43.8 | 1 | 3.7 |
| ZARN60120-L-TV | 60 | 120 | – | – | 103 | 74.5 | 25 |
| 105 | 90 | 105 | 17.5 | 38.5 | 16 | 0.3 | 0.6 |
|
| 106 | 88 | 187,000 | 550,000 | 44,500 | 92,000 | 2,700 | 950 | 4.2 | 5,300 | 4,300 | 54.5 | 1 | 4.85 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Automatic Color Printing Serviette Napkin Tissue Paper Folding Machine
>>
48′′ 55′′ Outdoor Indoor Kids Fitness Jumping Trampoline with Safety Protection Net and Basketball Hoop
>>
Multi Gas Analyzer Lel Co/H2s Nh3 O2 Portable Pump Multi-Gas Detector
>>
0.2W Water Drop Motion Sensor Wall Light LED Lamp
>>
New Water Pump Thermostat For BMW 135i 335i 535i 640i 740Li 11517588885
>>
UTM382 C4 C5 C6 C7 DL Automatic Envelope Plastic Film Window Patching Gluing Pasting Machine
>>
Agricultural New PP Plastic Clear Packaging Bags for Food
>>
Automatic Glass Machinery Factory Automatic Glass Process
>>
Chicken Spiral Cooling Tank in a Slaughter Machine Line
>>
Promotion Senior Economic Quick Proofing OEM Casting Design Spare Parts
>>
China Supplier Screen Printers PCB Machine Screen Printing Press Machine
>>
Automatic CE Approved Blow Molding Plastic Ocean Ball Making Machine
>>
3 Ply Type IIR Medical Surgical Mask (Tie-On) CE marked and meets the requirements of EN14683:2019 Type IIR
>>
Car Parking Shade PVC, Membrane Structure Tent, Membrane Tensile Structure
>>
Dbp 250 new thermoforming tablet and pill blister packing and sealing machine packaging machine price
>>
MQ168 A3 A4 A2 C3 C4 Semi Automatic Hydraulic Envelope Die Cutting Machine
>>
Galvanized Steel Vacuum Tubes Non-Pressurized Solar Water Heater
>>
Doosan steering cylinder seal kit for SD300 wheel loader
>>
China Factory 3/4 Saf Axles 45 Tons 60 Tons 80 Tons Customization Service Air Suspension/ Steel Plate Axles Dump Semi Trailer Tipper Trailer
>>
Quad Band GSM 850/900/1800/1900 2G Module MC55i MC55iW MC55i-W
