Product Details
Product Description
Product Description
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
| G60E00HAHF8LHXXM8LPXXUXXWXX |
TE: To prevent possible signal degradation, use a separate metal conduit run for both the sensor and signal/power wiring. Transmitter power passes through the signal leads. Under ideal conditions, the use of conduit and shielded wire may not be required. However, to avoid noise problems, enclose the sensor and signal/power wiring in separate conduit. Just prior to entering the housing, terminate rigid conduit and install a short length of flexible conduit to reduce any stress to the housing. Signal/power wiring must bear a suitable voltage rating, a temperature rating of 75-degrees Celsius (167-degrees Fahrenheit), and must be in accordance with all NEC requirements for the installation site. OTHER EQUIPMENT INTERFACE The transmitter has an isolated output and controls the loop current between four and 20 milliamperes depending on the range and PV values. Since the output is isolated, the instrument loop may have a maximum of one nonisolated device within its circuit. The maximum load on the current loop must not exceed the values shown in Figure 1-1. TRANSMITTER ROTATION The transmitter has four pairs of threaded mounting holes. Since these holes are located at the corners of the transmitter, it can be mounted in any of the four positions as shown in Figure 3-2. INSTALLATION SEQUENCE Refer to Figure 3-3 for the transmitter installation sequence. Each block of the flow represents a single task that must be completed before continuing with the sequence. In some cases, more than one path can be taken during installation. For paths that are in parallel, either complete all of the tasks in all of the paths before continuing or complete all of the tasks in only those paths that apply before continuing. At least one path must be completed. Some blocks contain alphanumeric codes. These codes identify the procedure that describes the steps to complete an INSTALLATION INSTALLATION SEQUENCE 3 - 4 WTPEEUI520002A1 indicated task. Complete all of the steps given in a procedure before continuing to the next procedure. The procedures have check boxes in the margin by each procedural step. When performing a procedure, check each box as each step is completed. By treating each task as a separate entity, the procedures provide an easy method for finding the information needed to perform each task in the installation sequence. Figure 3-2. Transmitter Rotation N O R OTAT IO N 90 R OTAT IO N o 2 70 R OTAT IO N o 180 R OTAT IO N o T03432A Figure 3-3. Installation Sequence TR4027A MOUNTING SCHEME? S TA RT HINGE WALL PA N E L PIPE DONE WIRING AND GROUNDING WALL PR5 MOUNTING PIPE MOUNTING HINGE MOUNTING PA N E L MOUNTING PR3 PR1 PR4 PR2 INTRODUCTION WTPEEUI520002A1 4 - 1 SECTION 4 - OPERATING PROCEDURES INTRODUCTION The Type TB82TE transmitter has six main operating modes: measure, calibrate, output/hold, configure, security, and secondary display. An operating mode has several programming states that contain functions specific to that mode. The transmitter has a built-in user interface through which all transmitter functions are programmed or monitored. In order to maximize the viewing area and minimize the space needed for the keypad, the patent-pending interface uses a custom LCD and four-button keypad. Instrument functions and programming prompts are available through two regions on the LCD. These regions include a primary area that shows the PV (conductivity) and a secondary area that displays text prompts for programming or auxiliary information. In addition to the user friendly interface, the transmitter has a group of icons that alert the user of an existing fault condition, diagnostic spike output, or a held output. These icons, located at the top of the LCD, only appear under the specified condition. Pressing the FAULT info smart key while in the measure mode allows interrogation of any fault condition.
>>
Maxy Fill Body Filler 70cc Syringe (Hard)
>>
Brand New Hot Sale Xz500 Horizontal Direction Drill Price
>>
Full Set off Grid Solar Energy System 5kw 10kw 20kw Solar Panels with Inverter and Battery
>>
Wireless Dual Band 1200Mbps Desktop USB WiFi Adapter 4.2 802.11AC WLAN Network Card
>>
High-Precision New Material Brass Mother Copper Alloy Wire Cutting Wire
>>
SIM Card 3G or 4G Biometric Fingerprint Time Attendance Device
>>
Rechargeable Clip 3 4 Flip 6 Flip 5 Pulse 5 Pulse 4 Boom Box 3 Portable Bluetooth Wireless Speaker Box
>>
Car Wheel Rim Cover Hubcap 15 inch For Prius NHW20 2004 - 2009 42602 - 47030
>>
Designer Slippers Slides Women Slippers Summer Platform Sandals Thick Heels Luxury Slides
>>
Factory Price Flat Die Pellet Poultry Cattle Animal Feed Pellet Product Line
>>
Mini coal making machine briquette maker complete set coal briquettes making machine
>>
Waterproof Butyl Rubber Tape Customized Automatic Production Machine
>>
Hsnc-500 Infrared Granite Bridge Saw Stone Cutter for Basin Countertop
>>
custom galvanized expanded metal mesh for fence or ceiling
>>
Dolls and Dolls Dolls and Dolls Toys
>>
Custom Made Printed Folding 3X3 10X10 Outdoor Event Aluminum Frame Pop up Tents Marquee Gazebo Canopy Trade Show Tent
>>
Class 100 and Class 1000 Cleanroom ESD Anti-Static Clean Safety Shoes
>>
High Efficiency Biomass Wood Sawdust Rice Husk Charcoal Briquette Making Machines
>>
My-M056A High Quality Dental Handpiece Kit Set Odontology Handpiece Kit
>>
Factory Price Stainless Steel Food Grade Chain Plate Belt Conveyor for Packing Machine
